Type 22 or Type 33: Which valve radiator is right for your room?
Two panels or three: the panel number determines how much heat a flat radiator emits from the same wall area and how far it protrudes into the room.

In short: You choose between Type 22 and Type 33 based on heat demand and space. The type number indicates how many panels and fin layers a panel radiator has: Type 22 has two, Type 33 has three. For the same size, Type 33 delivers significantly more heat, but protrudes further into the room and is heavier. Type 22 is sufficient for most rooms, while Type 33 is worth it for high heat demand on limited wall space or at low flow temperatures.
In February, you find out which room is pushed to its limits by its radiator. If you are then looking for a panel radiator, you will come across two numbers that appear everywhere: 22 and 33. They sound like sizes, but they describe the internal construction, which determines performance, depth, and weight.
What the type number reveals
A panel radiator consists of panels through which the hot water flows. Between and behind the panels are folded metal sheets, known as convection layers or fins. They increase the surface area from which the air absorbs heat. The type number describes this combination: the first digit indicates the number of panels, and the second indicates the number of fin layers.
- Type 22: two panels, two fin layers. Double-layer, compact, high performance for its depth.
- Type 33: three panels, three fin layers. Triple-layer, more performance on the same wall space, but deeper.
There are also other combinations, such as Type 11 with one panel and one fin layer, or Type 21 with two panels and one layer. They are slimmer but deliver less heat. The designation is commonly used across manufacturers, so you can roughly compare radiators from different providers using the type number. However, the exact performance always depends on the data sheet for the respective size.
Type 22 or Type 33: a direct comparison
The difference is clearest when you place both types side by side in the same size. The values apply to the KONRAD Type 22 and the KONRAD Type 33 in 600 × 1000 mm:
| Feature | Type 22 | Type 33 |
|---|---|---|
| Construction | 2 panels, 2 fin layers | 3 panels, 3 fin layers |
| Depth | 105 mm | 160 mm |
| Output at 75/65/20 °C | 1754 W | 2514 W |
| Output at 55/45/20 °C | 884 W | 1263 W |
| Weight | 31.92 kg | 47.24 kg |
The numbers following the output indicate the flow temperature, return temperature, and room temperature. At lower temperatures, both deliver significantly less heat, but the ratio between them remains similar. The triple-layer model extracts noticeably more heat from the same wall space, but pays for it with depth and weight.
When Type 22 is sufficient
For most living rooms, bedrooms, and children's rooms, Type 22 is the right choice. It is slimmer, easier to install, and available in many sizes. Type 22 is particularly suitable when:
- there is enough width under the window to achieve the required performance along its length,
- a deep windowsill, curtain, or piece of furniture leaves little space in front,
- the wall is less load-bearing, such as a lightweight partition wall,
- the room is well insulated and does not have a high heat demand.
If a room needs more heat, a longer Type 22 is often the simpler solution than a deeper Type 33. A Type 22 in 400 × 1600 mm delivers 2038 W at 75/65/20 °C and 1037 W at 55/45/20 °C, more than a Type 33 in 400 × 1000 mm with 1816 W and 924 W. The wall just needs to be wide enough.
When Type 33 is worth it
Type 33 plays to its strengths where a lot of heat is needed but little wall space is available. Typical cases:
- Short wall, high demand: An old building room with high ceilings, where only a short section of wall remains free besides the door and wardrobe.
- Low flow temperature: If the heating system runs cooler, the output of every radiator drops. A triple-layer model compensates for this better on the same surface area.
- Large room with only one radiator space: When there is only one wall on which a radiator can be hung.
- Replacement for an old, solid radiator: Old cast-iron or tube radiators often deliver a lot of heat on limited width. A Type 33 comes close.
When planning Type 33, allow for the additional depth, especially under windowsills and next to doors. And remember the weight: the wall must be able to securely support the brackets; if in doubt, a specialist company will check this.
How to distribute heat in large, open spaces across one or more radiators is explained in the article Open living and dining area: One radiator or two?. For small utility rooms, however, a short Type 22 is often sufficient, as shown in the article Radiators in the hobby room and basement. You can find all sizes in the living room radiators.
Frequently asked questions
Can I simply replace a Type 22 with a Type 33?
Often yes, if the size and connection location are suitable. With the KONRAD, the valve connection is at the bottom for both types, so the connection to the pipes remains similar. However, check whether there is enough space for the additional depth and whether the wall can support the higher weight.
How can I tell which type my old radiator has?
Look down through the cover grille or from the side into the radiator. You will see the smooth panels and the folded fins between them, and you can count both. The depth helps to check: a triple-layer radiator protrudes visibly further from the wall than a double-layer one.
Is Type 33 harder to clean?
Slightly. More dust accumulates between the three fin layers, and the inner areas are harder to reach. A narrow radiator brush and a vacuum cleaner with a crevice nozzle help, preferably at the beginning of the heating season.
Does a Type 33 heat up faster than a Type 22?
It delivers more heat and therefore usually brings a room up to temperature faster. However, how fast it really is also depends on the flow temperature, room size, and walls. A sufficiently large Type 22 can heat the same room just as well.
Double-layer or triple-layer
For most rooms, the KONRAD Type 22 is the right choice. If you need more heat on limited wall space, take a look at the triple-layer Type 33.


