Installation

Hemp, Teflon tape or sealing ring: What seals on which thread

The threads and fittings on the radiator are sealed differently. We explain what goes where, where hemp can even cause damage, and what the specialist company takes care of.

by Helia Bad Redaktion6 min read

Multiblock-Set in Anthrazit mit Thermostatkopf auf einer Travertin-Ablage

In short: You don't need to seal a radiator thread at every connection. Tapered threads seal within the thread itself, with hemp and sealing paste, sealing thread, or Teflon tape. Compression fittings, Euro cones, and fittings with flat or ring seals need nothing additional; hemp would even interfere there.

At the end of November, when there is little to do outdoors, many people take on small jobs around the house. A dripping connection on the radiator, a new thermostat head, a bathroom radiator that should be on the wall before Christmas. In the hardware store, hemp, Teflon tape, sealing thread, and sealing paste lie next to each other, and the question is: What goes where?

The answer does not depend on taste, but on the design of the connection. Those who know the principle also understand why some connection drips despite plenty of hemp.

Sealing radiator threads: two principles

There are two basically different ways to make a connection tight on heating pipes.

In the first principle, the thread itself seals. A tapered male thread that tapers towards the front is screwed into a sleeve. The further it goes in, the tighter it sits. To seal the fine gaps between the thread grooves, a sealant is put into the thread. Such threads are described by the DIN EN 10226 standard.

In the second principle, the thread does not seal, but a sealing surface. The thread is cylindrical and only holds the parts together. The actual sealing is done by a flat seal, an O-ring, a cone, or a compression ring. A sealant in the thread does nothing here. In the worst case, it prevents the sealing surface from sitting cleanly.

How do you recognize what you have in front of you? A look at the part helps. If a seal is included, there is a bundle with a smooth surface, an O-ring, or a cone, this surface seals. If all this is missing and the thread gets narrower towards the end, the thread itself seals. In data sheets, there is often a letter before the size: G for cylindrical, R for tapered male threads.

Hemp, sealing thread, and Teflon tape

For connections that seal in the thread, there are three common means:

  • Hemp with sealing paste: the classic on metal heating pipes. It is wound in the direction of the thread and brushed with paste. It forgives a small correction of the alignment by slightly unscrewing it more than other means.
  • Sealing thread: a plastic thread that is wound without paste. It can be processed cleanly and is popular with many plumbers.
  • Teflon tape: a thin PTFE tape, good for small threads. If a connection is unscrewed after that, it becomes slightly leaky.

Every means has its rules, for example regarding the quantity and the winding direction. Do not combine them, so no Teflon tape under hemp. For drinking water and gas, there are also separate requirements for the sealants, the heating system is a separate area.

Compression ring, Euro cone, and flat seal

Many connections on the radiator work without sealant in the thread. The most important:

Compression fitting

It connects a smooth pipe with a connection. When tightening the nut, a ring made of metal is pressed onto the pipe and seals there. Our Multiblock-Set is connected via such compression fittings, depending on the pipe in 15, 16, or 18 mm. No hemp belongs on the thread of the nut.

Euro cone

A cone with a sealing ring, common on manifold systems and many valves. The sealing is done by the cone with its ring, also without hemp in the thread.

Flat seal and O-ring

Union nuts on fittings, blind plugs, and some bleeders seal with a flat seal or an O-ring against a smooth surface. The connections of our bathroom radiators have cylindrical G-½″ threads. Which seal belongs to a plug is stated in the installation instructions of the radiator.

Connection Where it seals Sealant in the thread?
tapered thread in sleeve in the thread yes: hemp with paste, sealing thread, or tape
cylindrical thread with seal at flat seal or O-ring no
compression fitting ring on the pipe no
Euro cone cone with sealing ring no

Typical mistakes and how to recognize them

Leaky connections usually have one of a few causes. The most common: A sealant was used where the connection has a sealing surface. The hemp pushes the seal to the side, and it drips despite a tightly tightened nut.

Also common are too much or too little hemp, a damaged thread, a forgotten sealing ring, or a compression fitting that was placed diagonally. And sometimes it was simply tightened too tightly, so the seal or ring is crushed.

When changing the valve, the return connection also belongs to the thermostat valve, both are connected with suitable seals. A Thermostat valve set with ½-inch connection contains both parts. What the second valve on the radiator does, you read in Return connection. You can find all connection parts in the Radiator accessories.

Important: Work on pipes and fittings of the heating system belongs to the heating specialist company. It ensures that the system is drained, refilled, bled, and checked for tightness. You can prepare the parts yourself that sit on the radiator before installation, according to the instructions.

How the radiator is filled and checked after connection is described in our post Commissioning after installation.

Frequently asked questions

Can I combine hemp and Teflon tape?

No. Take either hemp with paste, sealing thread, or Teflon tape, and stick to the processing instructions. A mixture does not seal better, but rather worse.

Does hemp belong on blind plugs and bleeders?

Usually not, if they have their own seal or an O-ring. Then this seal seals against the sleeve. Decisive is the installation instructions of your radiator.

Why does a connection drip despite hemp?

Often, because a sealing surface is supposed to seal at this point and the hemp interferes with it. Also too little hemp, missing paste, or a backed-off thread are typical reasons. Let the specialist company redo the connection.

Can I loosen a compression fitting again and retighten it?

At the same place it can usually be reused, because the ring stays on the pipe. For a new pipe section, it needs a new ring. Decisive is that it is placed straight.

Unsure which part fits?

Write us pipe diameter, connection type, and radiator model. We will help you choose the connection block or valve set appropriately.

Send us a question View accessories

More on this topic:Installation

Radiator Finder

Find the right radiator in three questions

Question 1 of 3

How should the radiator be heated?
Replace an old radiatoropen the replacement finder (centre distance)

View calculation or consider flow temperature? Calculate the heating load for your room

More from the shop

Browse all models, sizes and colours.

View Radiator Accessories
  • Installation

    Wastewater connection for wall-hung toilets: What needs to match

    Between the toilet and the waste pipe are bends, sleeves, and seals. Which dimensions and parts must match for a wall-hung toilet, and when the specialist contractor takes over.

    6 min read

  • Installation

    Replacing a Toilet Seat: Dimensions and Mounting

    A new seat quickly freshens up the toilet. Which dimensions to choose, what matters when it comes to shape and mounting, and how to replace it step by step.

    6 min read

  • Installation

    Read the underfloor heating layout plan

    The installation plan shows the heating circuits, spacing, and the location of the manifold. Here is how to read it step by step and determine if it suits your room.

    6 min read