Replacing a Toilet Seat: Dimensions and Mounting
A new seat quickly freshens up the toilet. Which dimensions to choose, what matters when it comes to shape and mounting, and how to replace it step by step.

In short: To replace the toilet seat, you need three measurements: the distance between the two mounting holes, the length from the holes to the front edge of the ceramic, and the maximum width of the bowl. You also need to consider the shape, as an oval seat will not fit a square bowl. For wall-hung toilets, the seat is usually attached from above because there is hardly any room to reach under the ceramic. The replacement itself then takes only a few minutes.
A toilet seat wears out quickly: the surface becomes dull, the hinges loosen, and the lid slams. A new seat is one of the easiest ways to freshen up the bathroom, without a toolbox or a plumber's appointment.
Especially in summer, when renovations are already underway or a new wall-hung toilet is being installed, the question of the right seat arises. To make sure it really fits, it pays to take a close look at the measurements.
When a new toilet seat is worth it
Not every flaw requires a new seat. Loose hinges can often be tightened. In these cases, however, a replacement makes sense:
- The surface has cracks or deep scratches where dirt can settle.
- The hinges are corroded or can no longer be tightened.
- The soft-close mechanism no longer works, and the lid falls shut.
- You have a new toilet that the old seat does not fit.
When buying a new wall-hung toilet, it pays to check the scope of delivery. The LAVINNO Tornado Rimless wall-hung toilet includes a soft-close toilet seat and a wall-mounting kit, so a replacement will only be needed later.
These are the measurements you need for the toilet seat
It is best to measure the ceramic itself, not the old seat. It may be warped or may never have fit properly.
| Measurement | Where to measure | Note |
|---|---|---|
| Hole spacing | From the center of one mounting hole to the center of the other | Many hinges are adjustable within a certain range |
| Length | From the center of the mounting holes to the front edge of the bowl | The seat should not protrude at the front |
| Width | widest part of the bowl, measured on the outside | Flush on the sides looks best |
| Shape | outline viewed from above | oval, rounded, or square |
For the LAVINNO, the data sheet states a width of 365 mm and a projection of 490 mm, which is the distance from the wall to the front edge. You can find the hole measurements for the seat in the installation instructions or measure them directly on the holes. The article WC projection and space requirements describes how much space should be left free in front of a toilet of this size.
Tip: Place a large sheet of paper on the bowl, press it against the rim, and trace the outline including the mounting holes. Use this template to compare seats in the store.
The shape must fit
Toilet bowls have very different outlines. The classic shape is oval, while modern wall-hung toilets are often longer or have a more square contour. A seat that does not match the shape will protrude in one place and leave a gap in another. This not only looks untidy but also puts strain on the hinges when someone sits down.
Seat manufacturers therefore usually indicate which bowl shapes a model is designed for. Compare the length, width, and shape with your template before ordering.
Mounting from above or below
How the seat is attached to the toilet depends on the ceramic:
- Mounting from below: For many floor-standing toilets, the screw goes through the ceramic, and a nut is tightened underneath. This means you must be able to reach under the rim.
- Mounting from above: For wall-hung toilets, the space under the holes is often difficult to reach. Here, hinges use spreader plugs that are inserted from above and wedge into the hole when tightened.
When buying, make sure the seat is designed for the mounting method of your toilet. Many seats also feature a quick-release system: the seat can be removed with a single movement, making it easier to clean the hinge area. Together with rimless ceramic, this leaves hardly any corner where dirt can collect.
Replacing a toilet seat in five steps
- Loosen the old seat: Open the hinge cover caps, loosen the screws or nuts, and remove the seat.
- Clean the holes: Thoroughly clean the mounting holes and ceramic, and remove the old sealing washers.
- Insert the hinges: Insert the new mounting hardware according to the instructions, and do not forget the rubber washers.
- Align the seat: Place the seat on the bowl and move it so that it is flush with the bowl all around.
- Tighten with care: Tighten the screws evenly, but do not use excessive force. Too much force can damage the ceramic.
Finally, check that the lid closes gently and that the seat does not slip when you sit down. If it feels loose after a few days, gently tighten the screws again.
Important: If not only the seat but the entire wall-hung toilet is wobbly, the problem lies with the mounting of the ceramic. You can find out how to recognize this in the article Wall-hung toilet: How much can the wall support? In that case, you should contact a specialist plumbing company.
Frequently asked questions
Does every toilet seat fit every wall-hung toilet?
No. Hole spacing, length, width, and shape vary from model to model. Many seats cover a certain range with adjustable hinges, but the shape must match the bowl. Therefore, measure the ceramic before purchasing.
How can I tell if my toilet seat is attached from above?
Look under the rim of the ceramic behind the hinges. If you see nuts there, it is attached from below. If the screws are in plugs that are only accessible from above, it is attached from above.
What are the benefits of a soft-close mechanism on a toilet seat?
The seat and lid close slowly and quietly instead of falling onto the ceramic. This protects the hinges and ceramic and is convenient in a family bathroom. When buying, it pays to check whether the damping can be readjusted or replaced later.
A new wall-hung toilet for your bathroom
Rimless, glossy white, and supplied with a soft-close seat and mounting kit. You can find all the toilets in the shop in the overview.


