Faucet deck plate, multi-valve block, or thermostatic valve?
They are all located under the radiator and look similar, but they have different functions: valve block, multi-block, and thermostatic valve clearly distinguished from one another.

In short: A thermostatic valve controls the flow to a radiator with separate connections, usually a side connection, and works together with a return connection fitting. A multiblock combines control and shut-off for bathroom radiators with a center connection in a single component. A valve block is for valve radiators whose valve is already built in: it connects and shuts off the flow and return, but does not regulate them itself.
In mid-May, the heating is usually off, and this is a good time to plan changes to the radiator. If you are looking for accessories, you will quickly come across three terms that are often confused: valve block, multiblock, and thermostatic valve.
All three are located at the bottom of the radiator, and all three connect it to the pipes. However, their functions differ, and if you order the wrong component, you may not be able to connect the radiator at all, or only without control.
Thermostatic valve: control at a single connection
A thermostatic valve is located on the flow side of a radiator, where the hot water arrives. The thermostat head is placed on top. It measures the room temperature and presses a pin onto the valve, allowing more or less water to flow through.
Because the thermostatic valve only serves one connection, the other needs its own component: the return connection fitting. With it, the radiator can be shut off and often pre-set. The thermostatic valve and return connection fitting are therefore the typical solution for radiators with a side connection, where the connections are far apart on the left and right. They are available in an angled form for pipes coming out of the wall and in a straight-through form for pipes coming out of the floor.
Many thermostatic valves can also be pre-set. Using a scale on the valve, the heating specialist determines the maximum amount of water that can flow through. This way, every radiator in the house gets the amount of water it needs, and none of them makes noise or remains cold.
Multiblock: control and shut-off for the center connection
On a bathroom radiator with a center connection, both connections are located close together in the middle, usually 50 mm apart. Two separate valves would not fit there. The multiblock solves this: it accommodates the flow and return in a compact component.
Many multiblocks have a valve built in, on which a thermostat head is placed, and both sides can be shut off. The multiblock set in angled and straight-through form is available with compression fittings for 15, 16, or 18 mm and in the colors chrome, anthracite, white, and black. You choose the shape like with the thermostatic valve, depending on the direction of the pipes.
Valve block: the connection for valve radiators
Valve radiators already have the valve inside. On them, the valve insert is located at the top on one side, and the thermostat head is screwed directly onto the radiator. At the bottom, the flow and return come out close together.
A valve block connects these two connections to the pipes and can shut them off, for example if the radiator is to be removed or painted. It does not need to regulate, as the built-in valve takes care of that. The two-pipe valve block in angled form is designed for such valve radiators, for example for the KONRAD Type 22 and Type 33 flat radiators. It is available in angled and straight-through form.
Two-pipe means that the flow and return are carried in separate pipes. This is how most heating systems are set up. Older one-pipe systems work differently and need their own components; the heating specialist will clarify this.
Valve block and multiblock in direct comparison
The table summarizes what each component is designed for and what it does:
| Component | For which radiator | Regulates itself? | Thermostat head is located |
|---|---|---|---|
| Thermostatic valve | separate connections, usually side connection | yes, with head | on the valve on the flow side |
| Multiblock | center connection without built-in valve | yes, with head | at the bottom of the multiblock |
| Valve block | valve radiator with built-in valve | no | at the top of the radiator |
The most important distinction is therefore: If the radiator already has a valve built in, a valve block is sufficient. If it does not have one and has a center connection, you need a multiblock. With separate connections, you use a thermostatic valve and return connection fitting.
Three mistakes occur particularly often:
- Valve block on a bathroom radiator without a valve: The radiator is connected, but cannot be regulated.
- Multiblock on a valve radiator: Then there are two valves in a row that can interfere with each other.
- Wrong shape: Angled form and straight-through form are swapped, so that the component does not fit the pipes.
How you select the right version for your bathroom radiator step by step is shown in the article Which valve fits my bathroom radiator?.
Thermostat head: the common control part
Whether it is a thermostatic valve, multiblock, or valve radiator: in the end, a thermostat head is used for control. The M30 × 1.5 connection thread is widely used. A thermostat head with M30 × 1.5 connection fits most valves with this thread and regulates continuously.
You can change the head yourself, because it sits on the outside of the valve and has no contact with the heating water. How to do this is shown in the article Replacing a M30 × 1.5 thermostat head.
Important: The thermostatic valve, multiblock, and valve block are located in the heating water. Their installation and removal, as well as draining and filling, should be left to the heating specialist.
Frequently Asked Questions
Can I put a valve block on a bathroom radiator with a center connection?
Only if the radiator has a built-in valve, which is rare for bathroom radiators with rails. Without a valve, the heat could not be regulated. In this case, a multiblock is the right component.
Does a multiblock need its own thermostat head?
Usually yes, because the head sits directly on the valve in the multiblock. Check which thread the multiblock has; M30 × 1.5 is common. Then a thermostat head with this connection will fit.
Can I switch from a side connection to a multiblock?
Only together with a radiator that has a center connection and with pipes that arrive centrally underneath it. For this, the pipes usually have to be offset. This is easily doable during a bathroom renovation.
How can I tell if my heating system is a two-pipe system?
In a two-pipe system, each radiator has its own flow and return. This is the standard today. If you are unsure, for example in an older building, ask the heating specialist before you order a valve block.
Choose the right connection component
Valve block for valve radiators, multiblock for the center connection, thermostat head for control: everything for a clean connection under the radiator.


