Read the technical data sheet: This information counts with the radiator
Dimensions, performance, connection, pressure: a data sheet answers most questions before purchase. Here is how to read it step by step.

In short: The best way to read a radiator data sheet is in five steps: clarify the variant and units, check the dimensions and distances, compare the connection with your pipes, read the output with its temperature condition, and finally look at the pressure, weight, and water content. By following this approach, you can determine before purchase whether a model fits the wall, the pipes, and the heating requirements.
If an old radiator finally gives out in the middle of January or the spring bathroom renovation becomes concrete, the search for a new model begins. At the latest then, you end up with the technical data sheet, a table full of numbers, abbreviations, and standards.
It seems drier than it is. Most of the information answers very practical questions. We will go through them step by step using the example of the HALDEN in white in the size 60 × 160 cm.
Before reading: clarify the variant and units
A data sheet usually applies to an entire model range and lists each size in its own row. First, find the row for your variant. Then pay attention to the units: In the product name, the width and height are often in centimeters, in the data sheet in millimeters. 60 × 160 cm becomes 600 × 1600 mm.
Also read the order carefully. For bathroom radiators, width usually comes before height, for some flat radiators it is the other way around. A look at the table header saves confusion.
Dimensions and distances
Width and height tell you how much wall space the radiator needs. Two more dimensions determine how far it protrudes into the room:
- Depth: the depth of the radiator itself. For the HALDEN, it is 61 mm.
- Wall distance: how far the radiator sits from the wall with its brackets. For the HALDEN, it is 95–105 mm. The drawing in the data sheet shows from where to where it is measured.
The wall distance is important in a small bathroom if the door, shower door, or sink is nearby. It also determines how much air circulates behind the radiator and how well you can get behind it for cleaning.
Connection: type, center-to-center distance, thread
This part determines whether the radiator fits your pipes. Three pieces of information count:
- Connection type: center connection, side connection, or both. The HALDEN can be connected centrally or on the side.
- Center-to-center distance: the distance of the connections, measured from center to center. For the HALDEN center connection, it is 50 mm, the outer connections at the bottom are 550 mm apart at 60 cm width.
- Thread: usually G ½″. Valves, multiblock, or fittings are connected to it.
When replacing an old radiator, the center-to-center distance is the most important dimension. If it fits the existing pipes, nothing needs to be rebuilt. That is exactly what replacement radiators are for: The NORDVIK replacement bathroom radiator in white has variants with a center-to-center distance of 500 to 540 mm or 900 to 940 mm. This way, it meets the common connection dimensions of older bathrooms without having to chip away tiles.
Tip: Always measure the center-to-center distance on your old radiator from pipe center to pipe center, not from outer edge to outer edge. A difference of a few millimeters determines whether a replacement succeeds without conversion.
Output and its condition
The heat output is in watts, always together with three temperatures. They are determined according to DIN EN 442 and mean flow, return, and room temperature. For the HALDEN 60 × 160 cm, the data sheet states:
| Condition | Meaning | Output |
|---|---|---|
| 75/65/20 °C | classic heating with high flow | 937 W |
| 55/45/20 °C | low temperature, e.g. condensing or heat pump | 466 W |
Always compare radiators under the same condition. Some data sheets calculate with 55/45/22 °C instead of 55/45/20 °C, i.e. with a higher room temperature. For the replacement NORDVIK in white with 60 × 160 cm, it is 761 W at 75/65/20 °C and 364 W at 55/45/22 °C. Choose the value for your planning that is closest to your flow temperature.
Pressure, weight, and water content
At the end are details that are often overlooked:
- Operating pressure: The HALDEN is designed for 4 bar. The pressure of your system should be below that.
- Weight: 20.27 kg for the HALDEN 60 × 160 cm. Important for the wall and brackets.
- Water content: 8.33 l. It adds to the weight in operation and influences how quickly the radiator warms up.
Material, color, and scope of delivery
Finally, it is worth a look at the information about the product itself. For the HALDEN, it states structural steel as the material and a powder coating, with RAL numbers for colored variants, e.g. RAL 7016 for anthracite. The RAL number helps if you want to choose valves, hooks, or wall paint accordingly. The scope of delivery shows what is in the box. For the HALDEN, a mounting set with blind and bleed plugs is included, valves or a multiblock are to be ordered separately.
What weight and water content mean in detail for installation and filling is explained in the article Weight and water content. How quickly a bathroom radiator warms up in practice is under Heating time. You can find the data sheets of all models on the products under the bathroom radiators.
Frequently asked questions
Which output value applies to my heating?
The one whose flow temperature is closest to your system. For a modern condensing heater or heat pump, it is usually the value at 55/45 °C, not the one at 75/65 °C.
What is the difference between depth and wall distance?
The depth is the depth of the radiator itself. The wall distance describes how far it sits from the wall with its brackets. Which points are measured for this is shown in the dimensioned drawing in the data sheet.
Where can I find the data sheet of a radiator?
With us, it is on the product under the "Technical data sheet" tab. Keep it after purchase with the other documents for the bathroom, for later questions or an exchange.
Do I need to understand all the information to choose correctly?
No. For most purchases, dimensions, connection, and output at your flow temperature are enough. Pressure, weight, and water content become important during installation and filling.
A data sheet to try out
Open the data sheet of the HALDEN and go through the five steps once. After that, you will read every other data sheet faster.


