Maintenance

Radiator only partially warms up: Narrow down the causes

A radiator that only partially heats up often reveals where the problem lies with its pattern. Some of these issues are even completely normal.

by Helia Bad Redaktion6 min read

Thermostatventil-Set in Chrom mit Thermostatkopf zwischen Eckventil und Rücklaufverschraubung

In short: If a radiator only gets partially warm, the pattern reveals the cause: cold at the top indicates air, cold at the bottom indicates deposits or very low flow, and only one side warm indicates a throttled valve or an unbalanced system. Sometimes this is even normal, for example when the thermostat throttles down just before reaching the desired temperature. Check in the correct order before calling a professional company.

In early August, the heating is off, and most radiators are cold. If you had a radiator last winter that never got completely warm, you can now deal with the problem in peace. Repairs can be planned in summer without freezing, and professional companies usually have more time than in October.

To help you know what to tell the professional company or what you can check yourself, take a close look at the pattern of warm and cold areas on the radiator.

First check: Could this be normal?

A radiator does not always have to be equally warm everywhere. If the room is almost at the desired temperature, the thermostat only lets a little warm water through. This water cools down quickly on its way through the radiator. It is then warm at the top inlet, but only lukewarm at the bottom or on the other side.

This is intentional and saves energy. Only when the radiator is only partially warm even when the room is cool and the thermostat is fully open is there a fault. Therefore, always perform the counter-test first: turn the thermostat all the way up, let the room cool down a little, and feel it again after a while.

An oversized radiator also shows this picture more often. It quickly reaches the room temperature and is then only partially supplied with water.

Radiator only partially warm: what the pattern reveals

If the counter-test showed that something is wrong, this overview helps narrow it down:

Pattern Probable cause Next step
cold at the top, warm at the bottom air in the radiator bleed, then check pressure
cold at the bottom, warm at the top deposits, sludge flushing by the professional company
inlet side warm, rest cool low flow, valve throttled check valve pin and pre-setting
individual radiators weak, others hot missing hydraulic balancing professional company
all radiators only lukewarm flow, pump, heating times have the system checked

For air, the solution is usually simple. How to proceed is explained in the post Bleeding radiators. If a radiator becomes unusually hot while others remain cold, Radiator gets too hot helps with understanding.

The correct order of checking

With this order, you rule out the simple causes first:

  1. Open the thermostat all the way and wait for a while so that the radiator can be fully supplied with water.
  2. Compare: Are the other radiators in the house warm? If not, the problem is with the system, not the individual radiator.
  3. Check the valve pin, especially after summer, when it can get stuck.
  4. Bleed if the top part remains cold or if it gurgles.
  5. Read the pressure on the pressure gauge. If it is below the marked range, the professional company will top it up.
  6. Call a professional company if none of this changes anything.

Make a note of what you observed. A short report with photos saves the professional company time and you a long troubleshooting process.

Check the valve pin and thermostat yourself

Under the thermostat head is a small metal pin that opens and closes the valve. If the heating has been idle for months, it can get stuck. The radiator then remains cold or only warm at the inlet, regardless of how the thermostat is set.

This is how you check it: Remove the thermostat head, usually via a union nut or a clamping ring. The pin protrudes a little underneath. Press it in gently, it should spring back out. If it is stuck, moving it gently with the handle of a tool often helps. If it cannot be moved at all or water leaks out, it is a case for the professional company.

Important: You can remove the thermostat head and check the pin yourself. The valve body remains installed and sealed, no water flows out. Replacing the valve is an intervention in the heating circuit and belongs in the hands of the professional heating company.

If the valve is worn out, the professional company can replace it, for example with a Thermostat valve set in corner shape with ½″ connection. It consists of a thermostat valve and return connection, the head is fitted with M30 × 1.5.

When the professional company takes over

Many causes for partially warm radiators lie in the system itself. Sludge can only be removed by flushing, a poorly set pump or a missing hydraulic balancing can only be remedied with measured values. This is work for the professional heating company.

Sometimes the radiator itself is the problem, for example a very old radiator that is heavily sludged inside. Then a replacement is worth it, for example with a KONRAD Type 22 valve radiator. If you bought a radiator from us and suspect a fault with the device, write to us via Contact and Complaints, preferably with photos and your observations.

Frequently asked questions

Why do only some bars of my bathroom radiator get warm?

With low flow, the water first warms the bars near the inlet, the others remain cooler. With the thermostat fully open, this should balance out after a while. If the top bars remain permanently cold, there is usually air in the manifold.

Is a radiator that is warm on one side a cause for concern?

It is not dangerous. But it costs comfort, because the room warms up more slowly. If the counter-test with the thermostat fully open shows the same picture, it is worth looking for the cause.

Can a radiator that is too large remain partially warm?

Yes. A large radiator quickly brings the room to temperature, after that the thermostat only lets a little water through. Then it is often only warm at the top or at the inlet, and that is fine.

What should I tell the professional company beforehand?

What pattern you see, whether other radiators are affected, whether you have already bled and what pressure the pressure gauge shows. Photos of the radiator, valve and heating help additionally.

Radiator from our shop does not get warm?

Send us your pattern, photos of the radiator and valve and the pressure on the pressure gauge. We will help you classify it.

Contact us View all radiators

More on this topic:Maintenance

Radiator Finder

Find the right radiator in three questions

Question 1 of 3

How should the radiator be heated?
Replace an old radiatoropen the replacement finder (centre distance)

View calculation or consider flow temperature? Calculate the heating load for your room

More from the shop

Browse all models, sizes and colours.

View All radiators