Renovation

Extension or converted attic: Expanding the heating system

An extension or converted attic is intended to be as warm as the rest of the house. Here are the questions about heat demand, the system, piping, and radiators you should clarify while the walls are still open.

by Helia Bad Redaktion6 min read

Ventilheizkörper KONRAD Typ 22 in Weiß an einer hellen Wohnzimmerwand, daneben ein Leinensessel

In short: If you want to expand the heating system, you first need to determine the heat demand of the new room and then find out whether the heat source, pump, pipes and expansion vessel can handle the additional load. The new radiator must match the flow temperature of the existing system. Where it is not practical to run a pipe, an electric radiator is often the simpler solution.

Summer is construction season. Extensions grow, attics become bedrooms, offices or a second bathroom. And because the heating is not needed right now, a new heating circuit can be connected without anyone having to freeze.

Nevertheless, heating is often an afterthought in many extensions. Once the drywall and screed are finished, every pipe becomes a detour. The following questions should therefore be addressed at the beginning of the planning process.

Determine the heat demand of the new room

Every room loses heat through walls, roofs, windows and ventilation. A professional planner calculates how much according to DIN EN 12831, the standard for heat load. An extension built to today's standards often needs less heat than an old building room of the same size. In contrast, an attic with dormers and large roof windows can need surprisingly much because it has a lot of exterior surfaces.

For an initial assessment, a calculator is sufficient. It shows you the approximate size the radiator needs to be and helps with the conversation with the specialist company. If windows were also replaced in the existing building during the extension, the demand there will also change, as shown in the article New Windows, Old Radiators.

Is the existing system sufficient for the additional load?

An additional room is more than just an additional radiator. The heating specialist company checks these points before connecting it:

  • Heat source output: Older boilers often have reserves. Heat pumps are usually sized more tightly, so every room counts.
  • Flow temperature: The new radiator gets the same water as all the others. If it is too small, the heating curve for the whole house would have to be increased.
  • Pump and pipework: Long distances up to the attic place greater demands on the pump. The new circuit must not undersupply other rooms.
  • Expansion vessel: More radiators mean more water in the system. The vessel must be able to accommodate the additional expansion.
  • Balancing and control: After the expansion, the hydraulic balancing will be adjusted. With underfloor heating in the extension, a separate heating circuit with a mixer is often added.

Run pipes to the new room

It is usually connected to the nearest circuit. In the attic, it often goes through the ceiling or through the cold side, the low space behind the knee wall. It is cold there in winter. Pipes in unheated areas therefore need good insulation, otherwise they will lose heat or freeze in the worst case.

The order is important: lay the pipes, perform a pressure test, and only then close the walls. Determine where the flow and return will come out of the wall or floor before the drywaller arrives. With the KONRAD Type 22 valve radiator, for example, the flow and return can be connected from below on the same or opposite side. This gives flexibility, but does not replace a plan.

Tip: Photograph the open pipes with a tape measure in place before the walls are closed. This way you will know exactly where the pipes run later and where you can safely drill for radiator brackets, shelves or pictures.

Radiator, underfloor heating or electric?

Which solution is suitable depends on the room, its use and the system. The overview helps with the initial selection:

Solution Suitable if To be clarified
Water-filled radiator the room is used regularly and a pipe is easily accessible Output at your flow temperature, pipe run
Underfloor heating new screed is being laid in the extension anyway separate heating circuit, installation height, manifold
Electric radiator a small room is rarely heated or no pipe can be run there Electrical connection, operating times, safety zones in the bathroom

For living spaces in the extension, a low radiator like the KONRAD Type 22 is a natural choice. It is available in heights from 400 to 900 mm and widths from 500 to 2000 mm, so you will find a format for a parapet, knee wall or long wall. For a small bathroom under the roof that is only occasionally used, the electric HALDEN in white can be a sensible choice. It runs on 230 V and a heating element with 600 or 1200 W, depending on the size. The electrical connection is carried out by a specialist electrical company.

Expanding the heating system: the right time during construction

Those who plan the heating early save detours. A proven process:

  1. Estimate the heat demand and discuss the connection with the specialist company.
  2. Lay pipes in the shell structure, insulate them and perform a pressure test.
  3. Close the walls, complete the screed and surfaces.
  4. Install the radiator, fill the system, bleed it and balance it.

If the connection to the existing system is made in summer, there will be enough time until the heating season begins. Read more about seasonal planning in the article Radiator Replacement: Which Season Is Best.

Important: The connection to the heating system, filling, pressure setting and balancing are carried out by the heating specialist company. Electric radiators are connected by a specialist electrical company.

Frequently Asked Questions

How can I tell if my boiler can heat another room?

A look at the type plate is not enough. The specialist company compares the output of the heat source with the heat load of the entire house including the extension. With older boilers, there is usually headroom, but with tightly sized heat pumps, a precise calculation is worthwhile.

Does an extension need its own heating circuit?

Not necessarily. Radiators can often be connected to an existing circuit. In contrast, underfloor heating operates at lower temperatures and therefore often gets its own circuit with a mixer.

Does the entire system need to be drained for the connection?

That depends on where it is connected and whether there are shut-off valves there. Often it is sufficient to shut off and drain one part. After that, it is refilled, bled and the pressure is checked; the specialist company takes care of this.

When is an electric radiator worth it instead of a new pipe?

For small rooms that are rarely heated, or if a pipe can only be run there with great effort. For rooms that need to be warm for long periods every day, connecting to the central heating is usually the better choice.

How much heat does the new room need?

With the calculator, you can estimate how much output the radiator in the extension or under the roof should provide.

Calculate heat demand View all radiators

More on this topic:Renovation

Radiator Finder

Find the right radiator in three questions

Question 1 of 3

How should the radiator be heated?
Replace an old radiatoropen the replacement finder (centre distance)

View calculation or consider flow temperature? Calculate the heating load for your room

How much heat does your room need?

With the heating load calculator, you estimate the heat requirements of your room and find suitable models.

Calculate the heating load for your room

More from the shop

Browse all models, sizes and colours.

View All radiators